IRIXNetwork


  1. IRIX Network Forums
  2. SGI/MIPS
  3. SGI Discussion

Your hinv's (Post them here:)
#11
Re: Your hinv's (Post them here:)
Octane 2

Code:
<i>
</i>-bash-4.2$ hinv -v
2 400 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 2048 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
Integral SCSI controller 2: Version Fibre Channel AIC-1160, revision 2
Integral SCSI controller 3: Version Fibre Channel AIC-1160, revision 2
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: EMXI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
  PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 0
  PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 1

Code:
<i>
</i>-bash-4.2$ /usr/gfx/gfxinfo
Graphics board 0 is "IMPACTSR" graphics.
        Managed (":0.0") 1280x1024
        Product ID 0x3, 2 GEs, 2 REs, 4 TRAMs
        MGRAS revision 4, RA revision 0
        HQ rev B, GE12 rev A, RE4 rev C, PP1 rev E,
        VC3 rev A, CMAP rev E, Heart rev F
        20" monitor (id 0x3)
        Video board present

        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 75.92Hz (1280x1024_76)
 mimd
O2

Trade Count: (0)
Posts: 4
Threads: 1
Joined: Jun 2018
Find Reply
06-05-2018, 09:47 PM
#12
Re: Your hinv's (Post them here:)
THE OCTANE LIVES!
Here's the freshly-revived beauty's details

Code:
Octane 5# hinv -mv
Location: /hw/node
      PM10225MHZ Board: barcode HRX241     part 030-1272-002 rev  F
Location: /hw/node/xtalk/15
            IP30 Board: barcode GYK527     part 030-0887-005 rev  A
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode KBE699     part 030-0891-003 rev  G
    PWR.SPPLY.ER Board: barcode AAE2330120 part 060-0035-003 rev  A
Location: /hw/node/xtalk/12
            GM20 Board: barcode DZY140     part 030-0957-003 rev  G
1 225 MHZ IP30 Processor
Heart ASIC: Revision E
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
Main memory size: 1536 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: SSI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3

Code:
Octane 6# /usr/gfx/gfxinfo
Graphics board 0 is "IMPACTSR" graphics.
        Managed (":0.0") 1600x1200
        Product ID 0x3, 2 GEs, 2 REs, 0 TRAMs
        MGRAS revision 1, RA revision 0
        HQ rev B, GE11 rev B, RE4 rev C, PP1 rev A,
        VC3 rev A, CMAP rev E, Heart rev E
        unknown, assuming 19" monitor (id 0xf)

        (Could not contact X server; thus, no XSGIvc information available)
Octane Indigo2 R10000/IMPACT  I fix basket cases.
GRudolf94
O2

Trade Count: (0)
Posts: 31
Threads: 6
Joined: May 2018
Find Reply
06-08-2018, 05:54 PM
#13
Re: Your hinv's (Post them here:)
Finally got a working Octane:
Code:
<i>
</i>CarlsJr 1% hinv
1 300 MHZ IP30 Processor
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 512 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
  CDROM: unit 5 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: ESSI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
CarlsJr 2% /usr/gfx/gfxinfo
Graphics board 0 is "IMPACTSR" graphics.
        Managed (":0.0") 1280x1024
        Product ID 0x3, 2 GEs, 2 REs, 0 TRAMs
        MGRAS revision 4, RA revision 0
        HQ rev B, GE12 rev A, RE4 rev C, PP1 rev H,
        VC3 rev A, CMAP rev E, Heart rev F
        unknown, assuming 19" monitor (id 0xf)

        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
CarlsJr 3%
<IMG src="https://i.imgur.com/GK9gc2Q.jpg">[img]<URL url="https://i.imgur.com/GK9gc2Q.jpg">https://i.imgur.com/GK9gc2Q.jpg[/img]</IMG>
HP: C3000, B2600, 425T, RX2620, ZX6000, Vectra VA, DL360 G8
SGI:  :Octane:  R12k 300mhz, 400mhz for spares,  Visual Workstation 320 Single P3 W2K
IBM: RS/6000 43p, Intellistation Power 275, P5 505, Thinkpad 380D, 390
Sun: Ultra 45, Blade 2500, SS20, SS IPC (bad psu)
PA8600
O2

Trade Count: (0)
Posts: 9
Threads: 0
Joined: May 2018
Find Reply
06-15-2018, 08:15 PM
#14
Re: Your hinv's (Post them here:)
My Octane:
Code:
<i>
</i>Location: /hw/node
      PM20400MHZ Board: barcode KZT572     part 030-1476-001 rev  D
Location: /hw/node/xtalk/15
            IP30 Board: barcode HXX514     part 030-1467-001 rev  B
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode JLJ268     part 030-0891-003 rev  E
    PWR.SPPLY.ER Board: barcode AAE0230452 part 060-0035-002 rev  A
Location: /hw/node/xtalk/12
            GM10 Board: barcode GAK809     part 030-0938-003 rev  T
2 400 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 2048 Mbytes
Xbow ASIC: Revision 1.3
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: SI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
I am no longer posting from the moose, SGI O2 with R10k/250, 1GB RAM,  IRIX 6.5.27, unfortunately.
O2  1600SW  1600SW  Indy Indy Indigo  Indigo  Indigo2 R10000/IMPACT  Octane
jirka
Octane

Trade Count: (0)
Posts: 121
Threads: 4
Joined: May 2018
Location: Ostrava, Czech Republic
Find Reply
06-17-2018, 09:23 AM
#15
Re: Your hinv's (Post them here:)
<B>Indigo2 (Teal)</B>
Code:
CPU: MIPS R4400 Processor Chip Revision: 6.0
FPU: MIPS R4000 Floating Point Coprocessor Revision: 0.0
1 200 MHZ IP22 Processor
Main memory size: 320 Mbytes
Secondary unified instruction/data cache size: 1 Mbyte on Processor 0
Instruction cache size: 16 Kbytes
Data cache size: 16 Kbytes
Integral SCSI controller 0: Version WD33C93B, revision D
  Disk drive: unit 1 on SCSI controller 0
  CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version WD33C93B, revision D
On-board serial ports: 2
On-board bi-directional parallel port
Graphics board: GR3-Elan
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A2 revision 1.1.0
EISA bus: adapter 0
Got this system from ScutBoy a year or two back, but it wasn't working; the hard disk had failed in some manner that rendered it unbootable. Put off dealing with it for a long time because large-capacity 50-pin SCSI disks are so hard to come by these days - but it turns out the joke was on me, as when I finally opened it up, there was a perfectly good 9 GB secondary drive sitting in there and it was only the original 2GB system disk that wasn't working. Swapped that sucker over to the primary drive bay and set up a fresh IRIX install, and it was good to go Smile

I'm quite pleased with how usable this thing is considering its lower specs; I'm sure it'd lose out to my O2 in a straight benchmark fight, but it's no less usable, and the fans are <I>vastly</I> easier on the ears. Posted this from Netscape running on it, of course.
Computers: Amiga 1200, DEC VAXStation 4000/60, DEC MicroPDP-11/73
Synthesizers: Roland JX-10/SH-09/MT-32/D-50, Yamaha DX7-II/V50/TX7/TG33/FB-01, Korg MS-20 Mini/ARP Odyssey/DW-8000/X5DR, Ensoniq SQ-80, E-mu Proteus/2, Nord Lead 2, Behringer Model D
commodorejohn
PDP-X

Trade Count: (0)
Posts: 368
Threads: 7
Joined: May 2018
Find Reply
06-20-2018, 11:55 PM
#16
Re: Your hinv's (Post them here:)
After a year -or so- I revived my Octane. Three 512MB RAM modules went to the trash (I was thinking it was a motherboard failure). I very happy with her, just need a new fan for the powersupply (a loud panaflo is on the way).

Code:
octane2 4# hinv -v
2 400 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 2560 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
  Tape drive: unit 3 on SCSI controller 0: DAT
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
Integral SCSI controller 2: Version QL12160, low voltage differential
Integral SCSI controller 3: Version QL12160, low voltage differential
Integral SCSI controller 4: Version IEEE1394 SBP2
Integral SCSI controller 5: Version QL12160, low voltage differential
Integral SCSI controller 6: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V6
Integral Fast Ethernet: ef0, version 1, pci 2
Gigabit Ethernet: tg1, PCI slot 2 port 0
Gigabit Ethernet: tg2, PCI slot 2 port 1
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, levice 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x14e4, device 0x1648) PCI slot 2
  PCI Adapter ID (vendor 0x14e4, device 0x1648) PCI slot 2
  PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
  PCA Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
XT-DIGVID Multi-standard Digital Video: controller 0, unit 0, version 0x0
DMediaPro DM10 FW option: unit 0, revision 1.1.0
<ATTACHMENT filename="DSC_8521.JPG" index="1">     </ATTACHMENT>
<ATTACHMENT filename="DSC_8522.JPG" index="1">     </ATTACHMENT>


Attached Files Image(s)
   
Indigo Indy Indigo2 R10000/IMPACT O2 O2 Octane2 Fuel 1600SW 1600SW
Titox
Octane

Trade Count: (0)
Posts: 61
Threads: 1
Joined: May 2018
Location: Spain
Find Reply
06-21-2018, 06:10 PM
#17
Re: Your hinv's (Post them here:)
I bought <URL url="https://www.ebay.com/itm/Top-SGI-Silicon-graghic-Iris-Indigo-/263424706639?_trksid=p2047675.l2557&ssPageName=STRK%3AMEBIDX%3AIT&nma=true&si=BQgc5JMsuwS5h1Bz5GGybb4Y4mc%253D&orig_cvip=true&rt=nc">this 4K IRIS Indigo from eBay back in January, but I actually haven't got it to work until just a few weeks ago. It is my first SGI Smile

<ATTACHMENT filename="iris.jpeg" index="1">     </ATTACHMENT>

Both the CPU board and HD was dead on arrival, but the plastics were almost perfect. Just two small scuff marks on the front at the left side of the speaker grill that might be possible to remove. Not to mention the front door is fully intact. Anyways, bought a new HD and CPU board from Ian Mapelson. And a 4400 CPU. And 256 MB RAM... Elan gfx board... I have easily upgraded it for the same amount I bought it for Biggrin

<ATTACHMENT filename="1416.jpg" index="0">     </ATTACHMENT>
:Indigo: 150Mhz, R4400, 256MB, Elan, 6.5.22
Birchwood
O2

Trade Count: (0)
Posts: 2
Threads: 0
Joined: Jul 2018
Find Reply
07-03-2018, 07:38 PM
#18
Re: Your hinv's (Post them here:)
Nice one Birchwood, lovely and simply little machine. What's the highest Irix you can run on it?
No longer active. Please do not contact me.
Jacques
Tezro

Trade Count: (0)
Posts: 565
Threads: 53
Joined: May 2018
Location: UK
Find Reply
07-03-2018, 07:41 PM
#19
Re: Your hinv's (Post them here:)
<QUOTE author="JacquesT" post_id="1334" time="1530646915" user_id="104">
JacquesT post_id=1334 time=1530646915 user_id=104 Wrote:Nice one Birchwood, lovely and simply little machine. What's the highest Irix you can run on it?

Highest is 6.5.22 i believe, and also what i have on it.
:Indigo: 150Mhz, R4400, 256MB, Elan, 6.5.22
Birchwood
O2

Trade Count: (0)
Posts: 2
Threads: 0
Joined: Jul 2018
Find Reply
07-03-2018, 07:58 PM
#20
Re: Your hinv's (Post them here:)
Code:
Indigo2 1% hinv -v
FPU: MIPS R8010 Floating Point Chip Revision: 0.1
CPU: MIPS R8000 Processor Chip Revision: 2.2
1 75 MHZ IP26 Processor
Main memory size: 256 Mbytes
Secondary unified instruction/data cache size: 2 Mbytes
Instruction cache size: 16 Kbytes
Data cache size: 16 Kbytes
Integral SCSI controller 0: Version WD33C93B, revision D
  Disk drive: unit 1 on SCSI controller 0
  Tape drive: unit 2 on SCSI controller 0: DAT
Integral SCSI controller 1: Version WD33C93B, revision D
On-board serial ports: 2
On-board bi-directional parallel port
Graphics board: GU1-Extreme
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A2 revision 1.1.0
EISA bus: adapter 0

Code:
Indigo2 3% /usr/gfx/gfxinfo
Graphics board 0 is "GR2" graphics.
        Managed (":0.0") 1280x1024
        8 GEs, 2 REs, 24 bitplanes, 4 auxplanes, 4 cidplanes, Z-buffer
        GR2 revision 6, VB2.0
        HQ2.1 rev A, GE7 rev B,  RE3.1 rev A, VC1 rev B, MC rev D
        unknown, assuming 19" monitor
        Video board revision 3


Attached Files Image(s)
       
Indigo2 POWER Indigo2 75MHz R8000, 256MB/73GB, Extreme
biigD
O2

Trade Count: (0)
Posts: 27
Threads: 0
Joined: Jul 2018
Location: New York City
Find Reply
07-07-2018, 09:53 PM
« Next Oldest | Next Newest »


Forum Jump:


Users browsing this thread: 1 Guest(s)