HOLY H*LL...I just got to graphical PROM (using replacement V10..haven't tried "repaired" V10 yet). Also, no I didn't touch RAM slot...It's been broken all along (will show power-on log) so still needs fixing.
Okay, NVRAM is corrupted on every power-on (not powered reboot). DigiKey just sold out of snaphats too...but looks like mouser has them...so off to reload on snaphats and DIP sockets!
So EVERY fresh boot resulted in a halt. Every test was later done on POD mode stopped. Now that I have two terminals running for L1 and console I thought...why not just LET IT TRY TO GO without ANY POD mode debug diags.
Fresh boot COMPLAINED of LOTs of memory issues on bank #3, then invalid NVRAM, then forced into POD mode...did a reset switch. Now valid data for NVRAM...discovery normal..BOOTED RIGHT TO GRAPHICS!!!
Power button caused NMI errors and freezing (I'm assuming that's normal for ATX adapter?) at the end of the log. So memory error and resulting XBOW error are REAL but NOT considered unbootable...still need to look into this.
Bad NVRAM caused every fresh boot not to work anyway (hidden in console mode only). I still don't know about the "pre-power check" but that was INFO and not an error..so maybe that's the ATX adapter again? I'll ask the creator. DS1780 replacement was still needed on V10 to get ENV working.
So much to do but without further ado the VERY LONG boot log:
Code:
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
Running in DDR mode
*** Memory sizing failure:
*** Bank 2 (512 MB) and bank 3 (256 MB) sizes differ,
*** treating them both as 256 MB
Testing/Initializing memory ...........DIRECTORY MEMORY ERROR: Location DIMMs ADDRESS (backdoor) subtest
(dir. type is Standard) 001c01 2 & 3 0x90000001d8000000 Base Address
expected: 0x00000000aaaaaaaa
actual: 0x00000000aaa8aaa8
diff: ^x...........2...2
suspect devices = [Dimm3:G1A7B] [Dimm3:G1A7B]
DIRECTORY MEMORY ERROR: Location DIMMs ADDRESS (backdoor) subtest
(dir. type is Standard) 001c01 2 & 3 0x90000001d8000000 Base Address
expected: 0x00000000ffffffff
actual: 0x00000000fffdfffd
diff: ^x...........2...2
suspect devices = [Dimm3:G1A7B] [Dimm3:G1A7B]
DIRECTORY MEMORY ERROR: Location DIMMs ADDRESS (backdoor) subtest
(dir. type is Standard) 001c01 2 & 3 0x90000001d8000000 Walking Address
expected: 0x00000000aaaaaaaa
actual: 0x00000000aaa8aaa8
diff: ^x...........2...2
suspect devices = [Dimm3:G1A7B] [Dimm3:G1A7B]
DIRECTORY MEMORY ERROR: Location DIMMs ADDRESS (backdoor) subtest
(dir. type is Standard) 001c01 2 & 3 0x90000001d8000000 Walking Address
expected: 0x00000000ffffffff
actual: 0x00000000fffdfffd
diff: ^x...........2...2
suspect devices = [Dimm3:G1A7B] [Dimm3:G1A7B]
MBIST ERROR 0
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x1
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
expected data: 0x555555555 0x555555555 0x555555555 0x555555555
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 1
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x1
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
expected data: 0x555555555 0x555555555 0x555555555 0x555555555
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 2
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x1
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
expected data: 0x555555555 0x555555555 0x555555555 0x555555555
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 3
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x1
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
expected data: 0x555555555 0x555555555 0x555555555 0x555555555
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
************************************************
MBIST ERROR 0
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x555555555 0x555555555 0x555555555 0x555555555
expected data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 1
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x555555555 0x555555555 0x555555555 0x555555555
expected data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 2
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x555555555 0x555555555 0x555555555 0x555555555
expected data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
MBIST ERROR 3
************************************************
(DIRECTORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x00000000aaa80000
expected data: 0x000000000000aaaa
suspect devices = [Dimm3:G1B6B] [Dimm3:G1A7B]
[Dimm3:G1B6B] [Dimm3:G1A7B]
(MEMORY): Location: 001c01
DimmPair: 1
Bank: 1
RAS: 0x0
CAS: 0x0
actual data: 0x555555555 0x555555555 0x555555555 0x555555555
expected data: 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa 0xaaaaaaaaa
suspect devices = [Dimm 2 : F0A7B] [Dimm 2 : F0B6B]
[Dimm 2 : F5A7B] [Dimm 2 : F5B6B]
[Dimm 2 : B5A7B] [Dimm 2 : B5B6B]
[Dimm 3 : F0A7B] [Dimm 3 : F0B6B]
[Dimm 3 : E4A7B] [Dimm 3 : E4B6B]
[Dimm 3 : D9A7B] [Dimm 3 : D9B6B]
[Dimm 3 : C6A7B] [Dimm 3 : C6B6B]
[Dimm 3 : F5A7B] [Dimm 3 : F5B6B]
[Dimm 2 : C6A7B] [Dimm 2 : C6B6B]
[Dimm 2 : C1A7B] [Dimm 2 : C1B6B]
[Dimm 2 : B0A7B] [Dimm 2 : B0B6B]
[Dimm 2 : A4A7B] [Dimm 2 : A4B6B]
[Dimm 3 : A4A7B] [Dimm 3 : A4B6B]
[Dimm 3 : B0A7B] [Dimm 3 : B0B6B]
[Dimm 3 : B5A7B] [Dimm 3 : B5B6B]
[Dimm 3 : C1A7B] [Dimm 3 : C1B6B]
[Dimm 2 : E4A7B] [Dimm 2 : E4B6B]
[Dimm 2 : D9A7B] [Dimm 2 : D9B6B]
************************************************
TOO MANY ERRORS IN DIRECTORY MEMORY TEST: DimmPair: 1
DIMMs: 2 & 3
There were 4 errors found.
mtest_bank_dir failed: Walking Address
RSLT mtest_bank_dir FAIL diag_rc = 44 Walking Address
TOO MANY ERRORS DURING MEMORY BIST: DimmPair: 1
DIMMs: 2 & 3
Bank: 1
There were 8 errors found.
mtest_bank_bist failed:
RSLT mtest_bank_bis FAIL diag_rc = 48
Disabling the failed bank
.... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30359 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/01
\\\\Intializing any CPUless nodes.............. \\DONE
\*** Nasid 0: Memory bank 3 was previously Present & Enabled but is now Present & Disabled
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
\Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
NVRAM checksum is incorrect: reinitializing.
Automatic update of PROM environment disabled
PS/2 Keyboard & Mouse diagnostics
Found mouse on port 0
Found keyboard on port 1
PS/2 Keyboard & Mouse diagnostics passed
Graphics diagnostics
Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
Board version 1 - Buzz revision 2B
On board sdram size: 32 Mb
Cas latency: CAS 3
2 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics
Installing PROM Device drivers ............
Base I/O Ethernet set to /dev/ethernet/ef0
Installing Graphics Console...
graphics install: searching for pipe 0
Walking SCSI Adapter 0, (pci id 1)
1timeout on adapter 0 target 1
tm0=0xfffed7df04994b53, tm1=0xfffed7de39b49c50, timeout=0xb
- 2+ Device Vendor Product:
3+ Device Vendor Product:
4+ Device Vendor Product:
5+ Device Vendor Product:
6+ Device Vendor Product:
7+ Device Vendor Product:
8+ Device Vendor Product:
9+ Device Vendor Product:
10+ Device Vendor Product:
11timeout on adapter 0 target b
tm0=0xfffed7de39b49c5b, tm1=0xfffed7de39b49c34, timeout=0x3
+ Device Vendor Product:
12+ Device Vendor Product:
A 000: *** TLB Refill Exception on node 0
A 000: *** EPC: 0xc00000001fc47e58 (0xc00000001fc47e58)
A 000: *** Press ENTER to continue.
A 000: POD IOC3 Dex>
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
Running in DDR mode
*** Memory sizing failure:
*** Bank 2 (512 MB) and bank 3 (256 MB) sizes differ,
*** treating them both as 256 MB
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30359 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/01
\\\\Intializing any CPUless nodes.............. \\DONE
\Checking partitioning information ......... DONE
No other nodes present; becoming partition master
\Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
Automatic update of PROM environment disabled
PS/2 Keyboard & Mouse diagnostics
Found mouse on port 0
Found keyboard on port 1
PS/2 Keyboard & Mouse diagnostics passed
Graphics diagnostics
Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
Board version 1 - Buzz revision 2B
On board sdram size: 32 Mb
Cas latency: CAS 3
2 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics
Installing PROM Device drivers ............
Base I/O Ethernet set to /dev/ethernet/ef0
Installing Graphics Console...
graphics install: searching for pipe 0
Walking SCSI Adapter 0, (pci id 1)
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)
Walking SCSI Adapter 1, (pci id 1)
1- 2- 3- 4- 5- 6+ Device Vendor Product: TOSHIBA DVD-ROM SD-M1711
7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Initializing PROM Device drivers .......... DONE
A 000: *** NMI while in PROM on node 0
A 000: *** Error EPC: 0xc00000001306c038 (0xc00000001306c038)
A 000: *** Press ENTER to continue.
A 000: *** NMI while in PROM on node 0
A 000: *** Error EPC: 0xc00000001fc3ce08 (0xc00000001fc3ce08)
A 000: *** Press ENTER to continue.
Here's the HINV from PROM:
So I need to look through these errors but it seems to fail Bank 2 and Bank 3 segments on power-on and trim down working memory. I'll try cleaning first, obviously. But I'll need a new battery and possible an RTC and I'll need to look into this memory thing..but so far things are better. No confidence tests yet though so there could be more problems.
Upon further thought too, the "pre-power" error COULD be related to the fact that the power system cannot communicate with the PSU (can no longer auto-turn off) either.
NEED -> 