[Titox]

Hi Titox I tried that method but didn’t work for me. Did you have anything else setup beside those steps outlined in that post?

I don't remember anything extra to do. It was very straightforward. Is your USB card listed in hinv? With a NEC chipset?

I did my tests in a Fuel with the onboard USB subsystem. If the card was installed after IRIX the USB drivers can be missing.

[indy99]

Hi Titox I tried that method but didn’t work for me. Did you have anything else setup beside those steps outlined in that post?

I have a Graphire(1) connected to my Tezro and used exactly the same method as Titox. Guess it's probably worth mentioning I'm not using the Wacom supplied IRIX driver. Both the stylus/pen and the Wacom mouse that came with the Graphire are fully functional, though without the Wacom driver some advanced functions like scaling are not available.

If you chase the now dead links through nekochan back to Andreas' post on rootprompt.de, his workaround for the limited functionality was add *only* the Wacom control panel to the target IRIX system.

On the odd chance it might be helpful, I've attached an hinv from my Tezro with the Graphire attached and running. The USB kb&M and the Graphire are all attached to a USB KVM fed through a single USB connection to a four port USB PCI board in the Tezro:

Code:

hinv -vm                                                                              
Location: /hw/module/001c01/node
       IP53_4CPU Board: barcode NER934     part 030-1956-002 rev -C
Location: /hw/module/001c01/IXbrick/xtalk/11
       WS_INT_53 Board: barcode NBY982     part 030-1881-007 rev -A
Location: /hw/module/001c01/IXbrick/xtalk/12
       ODY128B1_2 Board: barcode NNB535     part 030-1884-005 rev -B
Location: /hw/module/001c01/IXbrick/xtalk/15
       WS_INT_53 Board: barcode NBY982     part 030-1881-007 rev -A
Location: /hw/module/001c01/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode MTT321     part 030-1771-005 rev -A
4 800 MHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 2.2
FPU: MIPS R16010 Floating Point Chip Revision: 2.2
CPU 0 at Module 001c01/Slot 0/Slice A: 800 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa
CPU 1 at Module 001c01/Slot 0/Slice B: 800 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa
CPU 2 at Module 001c01/Slot 0/Slice C: 800 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa
CPU 3 at Module 001c01/Slot 0/Slice D: 800 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa
Main memory size: 8192 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 4 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 5 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 6 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 7 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 3: Version SAS/SATA LS1068
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
  CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL12160, low voltage differential
Integral SCSI controller 4: Version IEEE1394 SBP2
  IEEE1394 Disk: node 30e00100001419 port 0 lun 0 on SCSI controller 4 (unit 2)
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
Graphics board: V12
Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
Iris Audio Processor: version MAD revision 1, number 1
  PCI Adapter ID (vendor 0x1000, device 0x0054) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x104c, device 0xac28) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
  PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 2
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 3
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 3
  PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 3
IOC4 firmware revision 79
IOC3/IOC4 external interrupts: 1
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
Dual Channel Display
IP35prom in Module 001c01/Slot n0: Revision 6.211
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB Human Interface Device: device id 0 type tablet
USB Human Interface Device: device id 0 type keyboard
USB Human Interface Device: device id 0 type mouse
USB controller: type OHCI

[tamtamx]

Hi guys, my intuos 2 and even 3 work with that tablet config file thanks all for the support. The only thing I’m missing now is that the mouse pointer is constraint to the position on the tablet. Right now it behaves more like a mouse a if that makes sense. Any idea if I can add some extra lines into the tablet config file to get that behaviour?
Going to see if even a recent wacom model is going to work with this.

[tamtamx]

An intuos 5 usb didn’t work on the tezro so the most recent that does work is the Intuos 3.

[indigofan]

Anyone know if the Intuos 3 will work on a Fuel leveraging built in USB?

[hamei]

Anyone know if the Intuos 3 will work on a Fuel leveraging built in USB?

I was never able to get one to work ... not properly, anyhow. Sort-of half assed but not something you'd want to use.

[michelangelo]

Hello. 

I was wondering if an Intous 2 USB will work with a USB to Serial adapter. Any idea or field experience ? Thx

[robespierre]

Hello. I was wondering if an Intous 2 USB will work with a USB to Serial adapter. Any idea or field experience ? Thx

Negatory.
"USB to serial" adapters only connect serial devices to USB host ports.