So everything seems ok when hooked to the L1 on the mainboard:
Code:
001a01-L1>log
02/02/24 18:30:13 checking power status
02/02/24 18:30:13 power up (COMMAND)
02/02/24 18:30:18 reset again MIPS
I attempted the reset but nothing changes.
Code:
001a01-L1>log
02/02/24 18:30:13 checking power status
02/02/24 18:30:13 power up (COMMAND)
02/02/24 18:30:18 reset again MIPS
02/02/24 18:32:09 NMI...
02/02/24 18:32:09 NMI (PANEL)
02/02/24 18:32:09 NMI done
Code:
001a01-L1>log clear
log reset.
But then hooking up to serial 1 I get nothing. I power on and still see nothing. Power off connect back to the L1 on the main board. Then do a power up again.
Code:
001a01-L1>log
02/02/24 18:33:20 Asterix SRAM low fault limit reached 0.000V.
02/02/24 18:33:34 L1 booting...
02/02/24 18:33:34 USB0: waiting on open
02/02/24 18:33:49 Reset...
02/02/24 18:33:49 reset (PANEL)
02/02/24 18:33:50 Reset done
02/02/24 18:33:54 Reset...
02/02/24 18:33:54 reset (PANEL)
02/02/24 18:33:54 Reset done
02/02/24 18:33:55 NMI...
02/02/24 18:33:55 NMI (PANEL)
02/02/24 18:33:55 NMI done
02/02/24 18:33:56 Reset...
02/02/24 18:33:56 reset (PANEL)
02/02/24 18:33:56 Reset done
02/02/24 18:33:57 checking power status
02/02/24 18:33:57 power up (PANEL)
02/02/24 18:34:02 reset again MIPS
02/02/24 18:35:09 1.5V low fault limit reached 0.719V.
02/02/24 18:35:44 L1 booting...
02/02/24 18:35:44 USB0: waiting on open
Code:
001a01-L1>env
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.94
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.00
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.07
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.35
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.47
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.47
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 4.99
3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.30
PIMM0 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.94
Asterix SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.54
Asterix CPU Enabled 10% 1.44/ 1.76 20% 1.28/ 1.92 1.61
PIMM0 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.49
PIMM0 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.30
PIMM0 5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 4.97
XIO 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.81
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.07
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.47
XIO 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.30
Description State Warning RPM Current RPM
-------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1228
FAN 1 HD Enabled 1560 2229
FAN 2 PCI Enabled 1120 1573
FAN 3 XIO 1 Enabled 1600 2185
FAN 4 XIO 2 Enabled 1600 4549
FAN 5 PS Enabled 1600 2229
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
-------------- ---------- --------- --------- --------- ---------
NODE 0 Enabled 60C/140F 65C/149F 70C/158F 36C/ 96F
NODE 1 Enabled 60C/140F 65C/149F 70C/158F 33C/ 91F
NODE 2 Enabled 60C/140F 65C/149F 70C/158F 27C/ 80F
PIMM Enabled 60C/140F 65C/149F 70C/158F 45C/113F
ODYSSEY Enabled 60C/140F 65C/149F 70C/158F 31C/ 87F
BEDROCK Enabled 60C/140F 65C/149F 70C/158F 39C/102F
I have another serial adapter I will try. But all I see is junk when using serial 1/2 on the back. But I'm assuming the baud rate is the same.
