L2 Controller Boot Loop
So with jan-jaap's instructions in hand, I built a plug to power an L2 controller I got off of eBay.
It powers up and talks to the serial terminal, however, she seems to be stuck. It's crazy though, because it's not your typical reboot loop, where she'd reach point x and start again. The device progresses into the loop and then reboots at random spots every time.
Here's the output from the console, idk if anyone has seen this before, but whatever tips you might have, I'm all ears...
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
ttyS02 at 0x0200 is a SCC
ttyS03 at 0x0300 is a SCC
WDT_8xx: Software Watchdog Timer version 0.3, 30 second timeout
block: queued sectors max/low 7805kB/2601kB, 64 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth0: FEC ENET Version 0.1, 08:fec: Phy @ 0x0, type 0x78100003
fec: link down
00:fec: 10 Mbps, Half-Duplex
69:11:bc:7b
PowerPC realtime clock driver, version 0.1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 00:04.0 (0000 -> 0002)
usb-ohci.c: USB OHCI at membase 0xc2002000, IRQ 8
usb-ohci.c: usb-00:04.0, PCI device 11c1:5802 (Lucent Microelectronics)
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: c2002000
hub.c: USB hub found
hub.c: 2 ports detected
Bad trap at PC: c0003f48, SR: 9032, vector=100
Oops: Exception in kernel mode, sig: 5
NIP: C0003F48 XER: A000297F LR: C0003F5C SP: C011BF70 REGS: c011bec0 TRAP: 0100
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c0119fe0[0] 'swapper' Last syscall: 120
last math 00000000 last altivec 00000000
GPR00: 00000000 C011BF70 C0119FE0 00000000 00000032 C02F9F28 C02F8000 00000000
GPR08: C01312E8 C0160C90 C02F8000 C01313D0 357D3F33 FE04412C FA200A00 C0160000
GPR16: C0110000 C0130000 C00A0000 C012E7D8 FA2▒
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
ttyS02 at 0x0200 is a SCC
ttyS03 at 0x0300 is a SCC
WDT_8xx: Software Watchdog Timer version 0.3, 30 second timeout
block: queued sectors max/low 7805kB/2601kB, 64 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth0: FEC ENET Version 0.1, 08:fec: Phy @ 0x0, type 0x78100003
fec: link down
00:fec: 10 Mbps, Half-Duplex
69:11:bc:7b
PowerPC realtime clock driver, version 0.1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 00:04.0 (0000 -> 0002)
usb-ohci.c: USB OHCI at membase 0xc2002000, IRQ 8
usb-ohci.c: usb-00:04.0, PCI device 11c1:5802 (Lucent Microelectronics)
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: c2002000
hub.c: USB hub found
hub.c: 2 ports detected
Bad trap at PC: c0003f4c, SR: 9032, vector=100
Oops: Exception in kernel mode, sig: 5
NIP: C0003F4C XER: E000087F LR: C0003F5C SP: C011BF70 REGS: c011bec0 TRAP: 0100
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c0119fe0[0] 'swapper' Last syscall: 120
last math 00000000 last altivec 00000000
GPR00: 00000000 C011BF70 C0119FE0 00000000 00000032 C02F3F68 C02F2000 00000000
GPR08: C01312E8 C0160C90 C02F2000 C01313D0 355A4833 FE04412C 04000000 00000001
GPR16: 00000000 00000000 00000008 00000000 FA20▒
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
Validating L2 Controller Flash image....OK
Booting...
Ethernet address from Motorola VPD EEPROM is 08:00:69:11:BC:7B
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.7-sgil2 (dsd@tstorm) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #1 Thu Aug 25 09:09:07 CDT 2005
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram panic=5
Decrementer Frequency = 187500000/60
Calibrating delay loop... 49.76 BogoMIPS
Memory: 11896k available (952k kernel code, 512k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
I/O resource not set for host bridge 0
Memory resource not set for host bridge 0
PCI: Cannot allocate resource region 0 of PCI bridge 0
PCI: resource is 80000000..7fffffff (100), parent c011c314
PCI:00:04.0: Resource 0: c0000000-c0000fff (f=200)
PCI:00:05.0: Resource 0: c0001000-c0001fff (f=200)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-8xx.o: i2c mpc8xx algorithm module
i2c-rpx.o: i2c RPX Lite/MBX module
i2c-dev.o: Registered 'rpx' as minor 0
i2c-core.o: adapter rpx registered as adapter 0.
Console: switching to frame buffer device
fb0: SGI L2 (SED137x LCD controller) frame buffer device
fb0: Display panel [mono]: Hantronix HDM3224 (320x240, 4-bit Greyscale)
CPM UART driver version 0.03
ttyS00 at 0x0000 is a SCC
ttyS01 at 0x0100 is a SCC
ttyS02 at 0x0200 is a SCC
ttyS03 at 0x0300 is a SCC
WDT_8xx: Software Watchdog Timer version 0.3, 30 second timeout
block: queued sectors max/low 7805kB/2601kB, 64 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth0: FEC ENET Version 0.1, 08:fec: Phy @ 0x0, type 0x78100003
fec: link down
00:fec: 10 Mbps, Half-Duplex
69:11:bc:7b
PowerPC realtime clock driver, version 0.1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 00:04.0 (0000 -> 0002)
usb-ohci.c: USB OHCI at membase 0xc2002000, IRQ 8
usb-ohci.c: usb-00:04.0, PCI device 11c1:5802 (Lucent Microelectronics)
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: c2002000
hub.c: USB hub found
hub.c: 2 ports detected
Bad trap at PC: c0003f18, SR: 9032, vector=100
Oops: Exception in kernel mode, sig: 5
NIP: C0003F18 XER: E000287F LR: C0003F5C SP: C011BF70 REGS: c011bec0 TRAP: 0100
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c0119fe0[0] 'swapper' Last syscall: 120
last math 00000000 last altivec 00000000
GPR00: 00000000 C011BF70 C0119FE0 00000000 00000032 C02F3F68 C02F2000 00000000
GPR08: C01312E8 C0160C90 C02F2000 C01313D0 35010833 FE04412C FA200A00 C0160000
GPR16: C0110000 C0130000 C00A0000 C012E7D8 FA200
 : R10K-195MHz, 1GB RAM, 146GB 15K, CD-ROM, AudioDAT, MaxImpact w/ TRAM. IRIX 6.5.22
 : R12K-400MHz, 1GB RAM, 300GB 15K, DVD-ROM, CRM Graphics, AV1/2 Media Boards & O2 Cam, DV-Link, FPA & SW1600. IRIX 6.5.30
 : 2 x R14K-600MHz, 6GB RAM, V12 Graphics, PCI Shoebox. IRIX 6.5.30
IBM : 7012-39H, 7043-140
|
