AUTODESK FLAME 2008 SERVICE PACK 6 - Printable Version

+- IRIX Network Forums (//forums.irixnet.org)
+-- Forum: SGI/MIPS (//forums.irixnet.org/forum-3.html)
+--- Forum: IRIX/Software (//forums.irixnet.org/forum-7.html)
+--- Thread: AUTODESK FLAME 2008 SERVICE PACK 6 (/thread-268.html)

---

AUTODESK FLAME 2008 SERVICE PACK 6 - Irinikus - 08-11-2018

I have finally managed to license my flame 2008 package thanks to gijoe77!

I have copied the Swr_license file to /etc and I have a problem in that I cannot setup a stonefs on my secondary disk in my Tezro.

I think that it's a problem with how the disk is partitioned.

Any help with this would be much appreciated!


<ATTACHMENT filename="IMG_4079.JPG" index="5">     </ATTACHMENT>

<ATTACHMENT filename="IMG_4080.JPG" index="4">     </ATTACHMENT>

<ATTACHMENT filename="IMG_4081.JPG" index="3">     </ATTACHMENT>

<ATTACHMENT filename="IMG_4082.JPG" index="2">     </ATTACHMENT>

<ATTACHMENT filename="IMG_4084.JPG" index="1">     </ATTACHMENT>

<ATTACHMENT filename="IMG_4083.JPG" index="0">     </ATTACHMENT>

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - bkd - 08-11-2018

Irinikus, make sure that string in swr file is ONE LONG string without breaks. As far as I remember there may be only one CR - at the end of this string.

PS: by the way - did you stop S&W before run sw_config?

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - bkd - 08-11-2018

You need "stonewire2008_filesystem_networking_guide.pdf", page 27 and walk step by step. Which step this error related to?

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - waldemar72 - 08-11-2018

I think you did not stopped stone&wire service before setting volumes for framestore. If I remember correctly you need do it - then you are allowed to "save device information", after starting sw service again it auto mounts volumes within framestore. Also if I see correctly you have marked "keep" gadget insted of "create" in upper left part of sw_config window. You need to mark create gedget because I suppose you want to create new framestore. I'm not sure because I'm far from machines.

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - waldemar72 - 08-11-2018

I'm sure swr string is correct, if not a green block marking disk 2 on controller 0 would be white with marking "unlicensed". So first stop sw (if i remember correctly stop_sw command in sw directory), then sw_config (remember - create), then start_sw. That's the magic.

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - waldemar72 - 08-11-2018

You said your problem is related to way your drive was partitioned. No, sw_config auto starts fx command and formats drive as needed.

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - Irinikus - 08-11-2018

You're right that I didn't stop the stonewire. (I didn't think it was necessary, as the system hadn't been setup before.)

I will fire up my Tezro and give it a try.

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - Irinikus - 08-11-2018

I followed the instructions, and this is what I got:


<ATTACHMENT filename="IMG_4090.JPG" index="0">     </ATTACHMENT>


Any ideas?

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - waldemar72 - 08-11-2018

Are you sure your drive is ok?
You could also try again with sw stopped, then in sw_config first clear or clear all, then again add+create. I had that issue as well but now I don't remember exactly what I did. I'll try tomorrow when I'll come back home.
Also reformating the drive in fx would be a good idea.

---

Re: AUTODESK FLAME 2008 SERVICE PACK 6 - Irinikus - 08-11-2018

<QUOTE author="waldemar72" post_id="2238" time="1534015633" user_id="301">

waldemar72 post_id=2238 time=1534015633 user_id=301 Wrote:Are you sure your drive is ok?
You could also try again with sw stopped, then in sw_config first clear or clear all, then again add+create. I had that issue as well but now I don't remember exactly what I did. I'll try tomorrow when I'll come back home.
Also reformating the drive in fx would be a good idea.

What type of drive should it be partitioned as? (root, option...?)

What type of file system? (xfs or efs?)

---